Hardness and Microstructural Characterization of Pack Carburizing AISI 1020 Low-Carbon Steel by Temperature and Holding Time Variations

Edi Santoso; Fatkhurrohman Fatkhurrohman; Addie Restu Firmansyah; Septian Candra Putra

doi:10.26877/asset.v6i1.17583

Hardness and Microstructural Characterization of Pack Carburizing AISI 1020 Low-Carbon Steel by Temperature and Holding Time Variations

Edi Santoso, Fatkhurrohman Fatkhurrohman, Addie Restu Firmansyah, Septian Candra Putra

Abstract

Recently, low-carbon steel is often used as a basic material for automotive spare parts on the market. This study aims to improve the quality of carbon steel which is not inferior to that made by manufacturers where the price is relatively affordable by carrying out pack carburizing. This study used the pack carburizing method, AISI 1020 low-carbon steel as a starting material and used fine coconut shell charcoal powder as a carbon source mixed with Na₂CO₃ as an energizer. Pack carburizing uses temperature variations of 850^oC, 875^oC and 900^oC, aims to find out how the results of hardness and microstructure values for variations of temperature and holding time. And also use SAE 20w-40 oil as a quenching medium. The highest hardness results were obtained on specimens with a heating temperature of 900^oC with a holding time of 60 minutes, with an average hardness value of 54.21 HRC. Accompanied by the phase formed, namely 61% pearlite 39% ferrite.

Keywords

hardness, microstructural, pack carburizing, AISI 1020, case depth

Full Text:

PDF

References

A. Nurharyanto, D. A. Halim, and E. Surojo, “Perbandingan Nilai Kekerasan Baja Karbon Rendah pada Proses Pack Carburizing dengan Media Arang Sekam Padi dan Arang Tempurung Kelapa,” Tek. J. Sains dan Teknol., vol. 15, no. 1, p. 39, 2019.

R. R. Sakura and D. D. Iskandar, “Pengaruh Variasi Karbon Aktif dan Waktu Tahan Terhadap Kekerasan Material JIS G-3123 Menggunakan Metode Pack Carburizing,” vol. 2, no. 1, pp. 31–35, 2017.

A. Azwinur, M. Yudi, and Z. Zulkifli, “Pengaruh media pendingin terhadap kekerasan dan ketangguhan hasil pengelasan material AISI 1050 pada proses las MAG,” J. POLIMESIN, vol. 18, pp. 124–130, 2020.

N. Maharjan, W. Zhou, and N. Wu, “Direct laser hardening of AISI 1020 steel under controlled gas atmosphere,” Surf. Coatings Technol., vol. 385, no. January, p. 125399, 2020.

R. Ramlan, “Efek Variasi Suhu Pack Carburizing Baja St 41 terhadap Kekerasan dan Kekuatan Impak,” Pist. J. Tech. Eng., vol. 4, no. 1, pp. 34–37, 2020.

M. M. A. Bepari, Carburizing: A Method of Case Hardening of Steel, vol. 2–3. Elsevier Ltd., 2017.

E. Sundari, R. Fahlevi, and B. Besar, “Mekanis Sprocket Imitasi Sepeda Motor Menggunakan Katalisator,” J. Austenit, vol. 10, no. 2, pp. 72–78, 2018.

N. Nurlina, R. M. Bisono, and D. Irawan, “Carburizing Menggunakan Media Arang Serbuk Gergaji Kayu Untuk Material Pisau,” vol. 8, no. 2, pp. 129–134, 2020.

American System for Testing Materials. “Standard Test Method for Rockwell Hardness of Metallic Material”. ASTM EE18-15, Oktober, 2020.

Joni, “Proses Pack Carburizing Menggunakan Arang Tempurung Kelapa,” F.SAINTEK. UNIRA Malang, vol. 05, no. 1, pp. 402–408, 2021.

A. Fikri, A. Rahman, R. Putra, and M. Habibi, “Carburizing Menggunakan Limbah Kulit Singkong Terhadap Sifat Fisik Dan Mekanik Baja 1020,” vol. 7, no. 2, pp. 110–114, 2023.

M. N. Nasution, “Analisak Ekerasan Dan Struktur Mikro Baja Aisi1020 Terhadap Perlakuan Carburizing Dengan Arang Batok Kelapa,” Bul. Utama Tek., vol. 15, no. 2, p. 165, 2020.

M. A. Rizki et al., “Pengaruh Proses Pack Carburizing Dengan Variasi Temparatur Dan Karbon Aktif Terhadap Kekerasan Permukaan Baja Aisi 1020,” vol. 6, no. 2, pp. 63–67, 2022.

T. A. Sutrisno and K. Malang, “KARAKTERISASI PROSES KARBURISASI BAJA AISI 1020 PADA TEMPERATUR 900oc MENGGUNAKAN LIMBAH SERBUK FOTOKOPI,” vol. 7, 2023.

A. Shaifudin, H. Istiasih, and A. Mufarrih, “Optimalisasi difusi karbon dengan metode pack carburizing pada baja ST 42,” vol. 1, no. 1, pp. 27–34, 2018.

N. López Perrusquia, M. A. Doñu Ruiz, E. D. García Bustos, M. lores Martínez, G. M. Urriolagoitia Calderón, and C. R. Torres San Miguel, “Duplex surface treatment on microalloy steels by dehydrated paste pack boriding and pack carburizing,” Mater. Lett., vol. 280, 2020.

D. Prayitno and S. B. Hengki, “Pengaruh Proses Pack Carburizing – Quenching Pada Kekerasan Baja Aisi 1020,” J. Penelit. Dan Karya Ilm. Lemb. Penelit. Univ. Trisakti, vol. 7, no. 1, pp. 45–52, 2022.

I. Azmy, D. Masruri, R. Rahardyanto, and Suyitno, “Pengaruh Proses Pack Carburizing Baja AISI 4340 Terhadap Peningkatan Kekerasan dan Ketahanan Aus,” J. Rekayasa Mater. Manufaktur dan Energi, vol. 5, no. 2, pp. 102–107, 2022.

D. Satria et al., “Pengaruh Waktu Tahan Proses Pack Carburizing Baja AISI 3115 dengan Menggunakan Calcium Carbonat dan Batubara Sub Bituminous dan Mendapatkan Perlakuan Panas Quenching Media Pendingin Air,” Rotasi, vol. 21, no. 2, p. 88, 2019.

D. P. Nurdin, “Analisis Sifat Kekerasan Dan Metalografi Pada Baja Aisi 1020, Aisi 1037 Dan Aisi 1040 Untuk Poros (Shaft) Dengan Menggunakan Proses Heat Treatmen,” Suara Tek. J. Ilm., vol. 13, no. 2, p. 13, 2022.

DOI: https://doi.org/10.26877/asset.v6i1.17583

Refbacks

There are currently no refbacks.

This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Advance Sustainable Science, Engineering and Technology (ASSET)

E-ISSN: 2715-4211
Published by Science and Technology Research Centre

Universitas PGRI Semarang, Indonesia

Website: http://journal.upgris.ac.id/index.php/asset/index
Email: asset@upgris.ac.id